I love Art... and a clean desktop. So, here is the one I use now
Painting by André Derain, "Landscape in Southern France", 1927
(Note the "start" button

I mistakenly deleted the Settings option from the menu.  Please tell me how I can get it back.
Thanks,
~Dick Mockler

I have done this on different setups but never on LL.
Anyway, I looked on the internet and found about three different ways depending on the version of Ubuntu. None of them worked.
This what I have done, open /etc/network/interfaces and made it look like this:

# interfaces(5) file used by ifup( 8) and ifdown( 8)
auto lo
iface lo inet loopback

iface enp0s10 inet static
    address 192.168.1.100
    network 192.168.1.0
    netmask 255.255.255.0
    broadcast 192.168.1.255
    gateway 192.168.1.1

Then  restart the network. That didn't work. Notice the "enp0s10" I normally use "eth0" but found this on a website somewhere.
Problem with the internet you can't tell if a thing is true or not.
Any help would be appreciated.

Hi folks,
I really wanted to try LL 4.0 on my Asus TP200SA laptop, which has 32GB of emmc memory soldered to the board. It originally came with Windows 10 which is insane taking into account the amount of memory this device has.While ago I replaced the Windows with Kali linux for some time, but i really didn't use it as much as i once intended so i decided to swap it for LL 4.0 (64bit).

I made a bootable USB with Etcher and disabled security boot in the BIOS settings, also enabled SMC which to my understanding is like legacy mode. My laptop recognized the USB and i proceeded to test the live version (I fell in love, props for the developers) At that point i started installing LL with the provided installer. I chose Erase Everything, installation went smooth and without errors, but after i restarted the computer it went directly into BIOS and doesn't even show the emmc memory as a option to boot from.

I read here on the forum that other people are having this problem too, but couldn't solve it for myself so i decided to ask. I saw somewhere that i should add bootie32.efi to /boot/efi on the usb but i cant find such thing anywhere. I would really appreciate any help from you  kind people.

PS I also tried with LL 3.2 32Bit, LL 3.8 32bit and 64bit all without success, except for Kali linux lite 64bit but i used UEFI settings to install it. 

Best Regards,
Acho

Install/remove software shows Clam anti virus as installed but it is not available in desk top. Tried to reinstall and got a error report . Can anyone advise please?

Please i would like to know is that looks ok? i have my file attached

i have used LL 3.8 in various situations with no problems.
Now install on an an Acer R1600. In both the live version and a version installed on a hard drive I have no mouse cursor. I can right click on the desktop and get the desktop menu but still no cursor.
I have tried this with both a wired USB mouse and a Bluetooth mouse with the same results.
Any help would be appreciated.

I successfully installed my HP Laserjet P1102w printer using hplip, and it works great.  However, each time that I reboot, the printer is gone and I must reinstall it.  This did not happen when I was using Ubuntu.  Any suggestions?
Thanks, mailmockler

I am editing my earlier post to explain my solution.  I am not sure why, but when I initially installed this printer with hplip, I took the approach of setting it up as a Network printer.  It installed fine, but upon rebooting, it had gone away.  So, I changed my approach, and used hplip to install it as a wireless printer.  I had to connect the printer to my computer with a printer cable, and when finished installing the printer, I was instructed to remove the cable and configure it.  After I removed the cable I rebooted and the printer was immediately found and functioned normally.  So, it looks now like the printer is properly defined and here to stay.

hello from mexico , fist time using linux , i kinnda wanna start coding but know absolutley nothing at all , im starting to reprogram o rewrite my own personal bios and habits and see where it takes me .

greetings

                                                            arturo

Just installed linux lite,  Asked me to do the updates.  Comes out an error log